F-GA4Q FUEL DISPENSER

F-GA4Q FUEL DISPENSER

FlowMeter Type : Optional

Accuracy :±0.2%

Pressure Loss (kg/cm) :Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume: 0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range :0~~99,999,999,99

Optional Display: Type LCD and Bright Backlight

Digit of Volume : 0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose :4.5m

Weight : 350kg

Dimension(L×W×H): 1660*660*2190(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 17

imbedded and exported from conc fuel dispenser rete base, filling in pipes hole with sand in case of diffusion of vapor. Delivery pipe in concrete should be a little higher, connected with corrugated pipe through flange and oil-resistant gasket. (See Diagram 5-2) Installation of pipeline and tank 3.1 The set of design of tank and pipeline should be conducted by locale design agency that has acquired ratification of public safety and firefight department with qualified capacity. In order to ensure system safety, filling station should not self –design pipeline of delivery oil. Diagram 5-3 is a pipeline installation sketch map of fuel dispensers and hydraulic system, which is provided for reference. The design and construction of filling station should conduct in accordance with the relevant stipulation of national standard GB 50156-2002 The Design and construction regulations of vehicle LP-Gas Station. Diagram 5-2: Connection chart of inlet pipe and corrugated pipe 3.2 Pipeline between fuel dispensers and tank fuel dispenser should be slant to tank. In hot whether pipeline slope regulated as 0.2% in GB50156 is easy to generate cavitation. Foreign fuel dispenser factories regulate larger slant such as Gilbarco 10ft (about 1.67%), Wayne 1:48 (2%). Thereby, it is suggested that the slant should be in scope of 1.5~~~ 2%. Diagram 5-3 Pipeline installation sketch map 3.3 Gasoline and diesel oil tank should be burred in earth under ground at least 0.5m fuel dispenser , prohibiting in indoor or basement. Tank should not be burred in the earth in which includes coal residue or chemicals, and surrounded by non-erosive material such as sand or thin earth, thickness no less than 0.3m. 3.4 The level distance between fuel dispenser and tank should be 20m or more as long oil could be suck without any leakage. The vertical distance between the inlet of fuel dispense and the nadir of oil level should not exceed 4m. The diameter of pipe between fuel dispenser and tank is 38m (1 1/2’�, which keeps clean with few elbows. The connection of delivery pipes

€The general format for a READ fuel dispenser message is given in the table below: Examples are given in　　Chapter 5.2.1.　　 Message Field Field Type Value Description　　 bin8 1 to 255　　 LNAR S　　 Logical Node Address Recipient　　 bin8 1 to 127　　 N　　 bin8 1 to 255　　 LNAO S　　 Logical Node Address Originator　　 bin8 1 to 127　　 N　　 bin8 0　　 IFSF_MC　　 Message Code　　 - the IFSF_MC is 0 for application messages　　 fuel dispenser bin8 000xxxxx Message Status　　 M_St　　 (bit map) - the message type is READ　　 - the token (xxxxx) is created by the originator　　 of the message　　FP2_1.90 fuel dispenser IFSF STANDARD FORECOURT PROTOCOL February 2006　　 COMMUNICATION SPECIFICATION　　Page: 16　　 bin16 Message Length　　 M_Lg　　 - the number of bytes in the READ-message　　 following　　 bin8 1 to 8 Database Address Length　　 DB_Ad_Lg　　

in a Room� a former state sena fuel dispenser tor, Seymour Lachman, describes how power is entrenched in the hands of the governor, the Senate majority leader (usually a Republican) and the Assembly speaker (usually a Democrat). These men often give their underlings just a few hours to review bills the size of phonebooks; lawmakers then vote as they are told, for fear of being denied aid for their districts. The capital is a playground for special interests, with more lobbyists per legislator (18 to one) than any other state. Public authorities, appointed bodies that pay for projects by issuing state bonds, are to blame for most of New York s debt. No one even knows how many authorities exist, though there are said to be “at least 733�of them. Thanks to gerrymandering, an inept legislator, once he has been elected, is usually there for life. Fixing this requires a bold leader. Mr Spitzer has audacity to spare. But as attorney-general he could act almost unilaterally. As governor he will have to compromis fuel dispenser e. The Spitzer campaign s favoured slogan is “Day one, everything changes� That is impossible. But he may nudge New York in the right direction.  © 2006 .  About sponsorship State elections Thinking local Nov 2nd 2006 | CHICAGO From The Economist print edition The battle for mansions and statehouses THE House and Senate are not the only prizes up for grabs fuel dispenser next Tuesday. With 36 races for governor and several finely balanced state legislatures, the parties are also slugging it out over control of the states. A wave of anti-Republican voting would help Democrats in a number of closely divided statehouses; and although 28 of America s governors are Republicans, the party is bound to take some losses as it tries to defend 22 of those spots at the polls this year. Some states are so evenly matched that a slight break either way could give one party total control. In Iowa, for example, the state Senate is split down the middl